1-877-PIPEMAN
1-877-747-3626
Hours: 7 AM to 4:00 PM Mon-Fri PST
Line Stopping Equipment and Supplies
Have you ever needed to replace a worn-out inline valve? It may be stuck open or have a small leak. There are times when you just can’t shut down or drain the system, but you need to replace the valve. Do you have a leaking saddle tee that needs to be replaced? Line Stopping allows you to block off the water on one side or two so you can remove a section of bad pipe or a stuck valve and replace it and then resume service without a major interruption. You complete a Hot Tap through the line stop saddle or sleeve, then use the Qualitech line stop machine to block off the water while the repair is being done. You then remove the line stop machine, insert a plug and cap and you are back in business.
Recommended For: Line Stops on Copper tubing
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Exact Fit 360 degree Gasket assures no electrolysis
- • Suitable for Water, Sewer (150 PSI)
- • Exact fit Full Circle GorillaGrip™ NBR Gasket Rated -40° to +180° F
Recommended For: Line Stops on Steel Pipe
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Exact Fit 360 degree Gasket assures no electrolysis
- • Suitable for Water, Sewer (150 PSI)
- • Exact fit Full Circle GorillaGrip™ NBR Gasket Rated -40° to +180° F
Recommended For: Line Stops on PVC Pipe
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Exact Fit 360 degree Gasket assures no electrolysis
- • Suitable for Water, Sewer (150 PSI)
- • Exact fit Full Circle GorillaGrip™ NBR Gasket Rated -40° to +180° F
Recommended For: Line Stops on Ductile Iron Pipe
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Exact Fit 360 degree Gasket assures no electrolysis
- • Suitable for Water, Sewer (150 PSI)
- • Exact fit Full Circle GorillaGrip™ NBR Gasket Rated -40° to +180° F
Recommended For: Line Stops on Asbestos Cement Pipe
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Exact Fit 360 degree Gasket assures no electrolysis
- • Suitable for Water, Sewer (150 PSI)
- • Exact fit Full Circle GorillaGrip™ NBR Gasket Rated -40° to +180° F
- • Type 1 and 4 - Recommended for: CI, DI, ACP, PVC and pipes suceptible to breakage
- • Type 2, 2E, 2ESS, 3, 5 - Recommended for: cast iron, ductile iron, C900/C905, PVC, HDPE and steel
- • Push Pin or Threaded Styles
- • Sizes: 4" to 12" and 4" to 24"
Recommended For: Line Stops on Steel Pipe
- • Available for 1.00”, 1-1/2”, 2.00”, 2-1/2”, 3.00”, 4.00” and 6.00” Line Stops
- • Outlet: Schedule 80 Carbon Steel seamless and machined
- • All outlets are "Male Threaded NPT" outside and inlets threaded NPT inside
- • Rated to Maximum 200 PSI and Maximum 300° F
Recommended For: Line Stops on Steel, Copper, DI, AC, PVC Pipe
- • Model 1001 - for 3/4" and 1" Line Stops/ Model 1251 - for 1-1/4" and 1-1/2 Line Stops
- • Model 2001 - for 1-1/2" and 2" Line Stops
- • Model 4001 - for 3" or 4" Line Stops/ Model 6001 - for 6" Line Stops
- • Base unit online includes plug setter, Complete units have everything recommended by the manufacturer
Recommended For: Steel, Copper, Ductile Iron
- • Available in Sizes: 6.00" to 36.00"
- • Cut-down service available
- • Made of special Urethane mix for maximum line stopping
- • For use with Schallert Line Stop heads
Recommended For: steel, aluminum, brass, cast iron, plastic or wood
- • 1-7/8" cutting depth (Deepest standard cutting depth available)
- • Available in 9/16” to 6.00” diameters
- • M-42 Cobalt Bi-Metal Construction - Up to 24% Longer Life
- • 4/6 variable tooth design and Thin 0.044" Kerf for faster and smoother cuts
Recommended For: Wood laminates, fiberglass, plywood or tile.
- • 1-5/8" cutting depth (Deepest standard cutting depth available)
- • Available in 11/16” to 6.00” diameters
- • 3 teeth per inch for smoother cut
- • Provides up to 10 times greater tool life on abrasive materials
Recommended For: steel, aluminum, brass, cast iron, plastic or wood
- • 1-7/8" cutting depth (Deepest standard cutting depth available)
- • M-42 Cobalt Bi-Metal Construction - Up to 24% Longer Life
- • Available in 7 to 20 piece kits for electrical, plumbers etc.
- • Includes: Mandrels, Adapters and Carrying Case
Recommended For: steel, aluminum, brass, cast iron, plastic or wood
- • Available in 7/8” dia to 6.00” diameters and 3.25, 4.50 or 6.00” Drill Depths
- • M-42 Cobalt Bi-Metal Construction - Up to 24% Longer Life
- • Uses any standard or Heavy Duty Mandrel
- • 4/6 variable tooth design and thin 0.044" Kerf for faster and smoother cuts
Recommended For: Wood laminates, fiberglass, plywood or tile
- • Available in 7/8” dia to 6.00” diameters and 3.25, 4.50 or 5.70” Drill Depths
- • Carbide-Tipped teeth: Efficiently cut abrasive materials
- • 3 teeth per inch for smoother cut
- • Provides up to 10 times greater tool life on abrasive materials
Recommended For: Primary Hot Tap use on: ACP, CI, DI, CLMC, and PCCP Pipe
- • Relton STHS Hot Tap Cutters made specifically for TM-1 Pro Series Hot Tap machine
- • Carbide Tipped Shell Cutters with standard 5-hole or 7-hole hole saw back-plate
- • Select Hot Tap Sizes for 4" to 6" Hot Taps with 3.375" drill depth
- • Can be re-tipped or resharpened
Recommended For: metal, plastic, wood, laminates, tile and more
- • Stock sizes 11/16" to 4" diameters
- • Complete - Includes carbide hole saw, 1/2x3 Shank, Ejector Spring, and Steel pilot
- • HO - Only includes carbide hole saw
- • Special order up to 40” diameter and 48” drill depth
Recommended For: All Blu-Mol Standard Hole Saws
- • Works with all Standard Hole Saws
- • Arbors
- • Pilots
Recommended For: All Relton Hole Saws
- • Arbors
- • Pilots
- • Ejector Springs
